PYRODRONE F4 OSD V2.3
$55.95
Please make sure to jump the correct selection for your VTX. If you want to use the VTX PIT mode function please type the following in the CLI command line:resource pinio 1 A15 (Hit Enter)Set pinio_box = 39 (Hit Enter)…
Out of stock
If you want to use the VTX PIT mode function please type the following in the CLI command line:
resource pinio 1 A15 (Hit Enter)
Set pinio_box = 39 (Hit Enter)
Save (Hit Enter)
Assign a switch to the VTX PIT option in Betaflight MODES tab.
If you decide mounting the FC upside with USB to the left side of the drone to benefit from the clean flat back of the board
remember to change the board orientation in the Betaflight configuration page like in the below image.
Check the below Race footage from MewoFPV Cory Ibanez 1st place winner at the Nytfury VS Dolma Callout Race using the PyroDrone F4 OSD Flight Controller.
Assign a switch to the VTX PIT option in Betaflight MODES tab.
If you decide mounting the FC upside with USB to the left side of the drone to benefit from the clean flat back of the boardremember to change the board orientation in the Betaflight configuration page like in the below image.
Check the below Race footage from MewoFPV Cory Ibanez 1st place winner at the Nytfury VS Dolma Callout Race using the PyroDrone F4 OSD Flight Controller.
Straight gold. The US currency should be backed by this FC! (Cory Ibanez)
If you have V2.2 or V2.3 Boards please adjust the voltage scale in the Betaflight Power and Battery page as follows:
HyperLite F4 OSD
One of the most popular FC is back and better than ever, combining an industry favorite layout with new feature sets for freestyle, long range, and racers. Finally, a board for every pilot!
The new Hyperlite F4 OSD takes the same celebrated flat-bottomed layout (crucial for clean and tight builds) and adds a much appreciated OSD and SIX UART ports (more than any other board on the market!) for GPS, RX, SmartAudio, and even Camera Control.
And with more features, comes improved ease of use with a built in 4-in-1 ESC socket and included harnesses for HobbyWing 45Amp G2 ,AiKON AK32, and Spedix GS35 4in1 ESCs. The built in solder pads mirror the 4in1 pad layout, so you can easily connect ANY ESC to this board to get features like current sensing and ESC telemetry (for the BL32 guys).
PLEASE NOTE: The Hyperlite F4 OSD uses its own BF target .bin, PYRODRONEF4.
Tech Specifications:
MPU6000 Gyro
STM32F405 CPUE @ 168mhz, can be overclocked
2-6S direct battery input
3.3V 100ma, 5V 1.2A BEC
5V Camera Power
Built in configurable Betaflight OSD
Flat bottom PCB for SUPER CLEAN builds
36×36 PCB with 30.5×30.5 mounting holes
6 UARTS. UART1 (INVERTER FOR SBUS),
UART2 (FREE),
UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off
UART4 (Free),
UART5 (Smart Audio)
UART6 (Free)
Built in 4 IN 1 ESC socket(including ESC telemetry, External current sensor)
Plug and plug with the most popular 4-in-1 ESCs (HobbyWing, Airbot, Spedix, Aikon),with supplied cables
Built in solder pads mirror of the 4-in-1 ESC socket
Printed layout instructions ON the board – no need for instructions!
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.